CEI-25G-LR and CEI-28G-SR offered in a 100G quad configuration in TSMC 28nm HPM process
Camarillo, California - September 04, 2013 -- Semtech Corporation. (Nasdaq: SMTC), a leading supplier of analog and mixed-signal semiconductors, today announced that its Snowbush IP group will ship a new Silicon Intellectual Property (SiIP) platform supporting Common Electrical Interface (CEI) standards up to 28 Gigabits per second (Gbps) for deployment in high data-rate chip-to-chip and chip-to-module applications.
The SBMULTC2T28HPM28G SiIP PHY is targeted for the new generation of chips supporting emerging Exascale computing, Terabit networking, and Petabyte storage markets. Each of these markets requires a PHY developed in a CMOS-based process to support the large digital gate counts necessary in today’s SOCs. The PHY is capable of being deployed in a multi-lane macro to support the highest I/O bandwidth possible with the lowest power per bit transferred.
“We are working with Semtech-Snowbush IP, using our extensive high speed experience, to provide a high-quality solution with fully characterized operation of the 28G PHY platform on the TSMC 28nm HPM process node,” said Naveed Sherwani, CEO of ASIC design firm Open Silicon. “This ultra-low power and high-performance SerDes combined with our implementation experience will allow us to enable our ASIC customers to bring unique and differentiated solutions to market.”
“Semtech-Snowbush IP has developed mixed-signal IP for more than ten years and our IP is in products shipping in millions of units per year,” said Roger Levinson, Vice President and General Manager of the Strategy and Systems Innovation Group at Semtech. “This new generation of IP targets the chip-to-chip and chip-to-module SOC/ASIC networking market requiring 25Gbps speeds to maximize I/O bandwidth. We are leveraging our years of experience developing platform-based SerDes/PHYs to provide performance and flexibility, while continuing to focus on efficient delivery and superb customer support.”
The SBMULTC2T28HPM28G SiIP PHY can be programmed to support multiple standards each with specific electrical performance characteristics. The area, power and latency have been optimized to minimize the impact when used in an SOC, ASIC or ASSP. A post-silicon tuning capability allows customers to adapt the performance of the PHY to different operating environments.
The new platform represents the eighth generation of a programmable analog front end that Semtech-Snowbush IP pioneered for handling many standards from a single silicon macro. The architecture was initially developed at 65nm and was ported to 40nm. At 28nm, the architecture has seen three generations of silicon and is shipping in production.
About the SBMULTC2T28HPM28G IP Platform
The SBMULTC2T28HPM28G has an analog front end (AFE) that includes the transmit (Tx) and receive (Rx) path circuitry along with auxiliary blocks for clock generation, test and biasing. The Tx driver is a highly programmable block including multiple registers to allow adjustment of TX amplitude, de-emphasis and pre-emphasis.
The Rx path is also highly programmable to meet the requirements of many serial I/O applications. Advanced equalization compensation reacts to the actual channel characteristics and extracts clean data that is provided to the on-chip parallel interface. Firmware supports the calibration and adaptation in both the Rx and Tx data paths. Implemented through a digital control interface, the software provides a flexible means of adjusting performance to meet different channel characteristics.
The Rx architecture includes a multi-stage continuous time linear equalizer (CTLE), passive linear equalizer (PLE) and variable gain amplifier (VGA). The receive path also includes a decision feedback equalizer (DFE) for crosstalk suppression and extended reach. All stages feature digital offset calibration and adaptive equalization to handle a range of channel conditions. The Rx architecture supports both AC and DC coupling.
The RX also includes a high bandwidth data clocked CDR to achieve high jitter tolerance. The CDR relies on a digital architecture and includes a sampling phase adjustment capability.
The receiver includes a non-destructive on-chip eye monitor to allow the user to “see” the eye opening at the receive slicer after the application of both transmitter and receiver equalization. This capability can be used to help adjust the transmitter and receiver equalizers and characterize link margin.
The TX architecture includes a source series terminated (SST) transmit driver with a feed forward equalizer (FFE). The FFE has per-cursor and post-cursor taps with both manual and adaptive control.
The TX clock generation is based on a fractional-N LC-PLL for superior jitter performance. An advanced, digitally assisted calibration approach is supported by firmware (same as Rx). Digitally controlled calibrations include TX termination, TX PLL frequency, TX PLL amplitude, TX phase alignment and DCD. Optional digital control supports link training.
The SBMULTC2T28HPM28G includes a minimal latency on-chip digital interface. Multiple parallel interface widths are supported and the digital interface is designed to inter-operate with industry available PCS and MAC (link) layer logic.
Key Features of the SBMULTC2T28HPM28G IP Platform
- Aggressive low-power design approach delivers maximum power savings at high speeds
- Numerous equalization schemes are included to address a wide range of channel applications and crosstalk challenges
- Automatic calibration of key circuits to maximize performance and yield
- Programmable TX driver including amplitude and multi-tap TX equalizer
- Programmable RX equalizer including CTLE, AGC and DFE
- Silicon option without DFE for increased power savings in shorter reach applications
- Support for both AC- and DC-coupled channels
- Flexible and low-jitter clock generation based on an fractional-N LC-PLL
- Scope-on-a-chip eye monitor for on-chip performance observation
- On-chip bit error rate tester (BERT) supporting multiple PRBS and user-defined patterns
- Eight separate loopback modes
- Analog DC test pad and digital status test bus
- AC JTAG scan chains
Pricing and Availability
The Silicon IP PHY (product code: SBMULTC2T28HPM28G) will ship in October (as GDS). System-level models are available today under NDA for performance testing and integration. Semtech offers comprehensive design-in assistance, including field- and factory-based support. Other information is available on www.semtech.com/snowbush. Please contact firstname.lastname@example.org for pricing information.
Semtech Corporation is a leading supplier of analog and mixed-signal semiconductors for high-end consumer, computing, communications and industrial equipment. Products are designed to benefit the engineering community as well as the global community. The company is dedicated to reducing the impact it, and its products, have on the environment. Internal green programs seek to reduce waste through material and manufacturing control, use of green technology and designing for resource reduction. Publicly traded since 1967, Semtech is listed on the NASDAQ Global Select Market under the symbol SMTC. For more information, visit www.semtech.com.